The convenience of a gas stove is known to anyone who owns one. But what if your auto ignition gas stove stops working? It can be frustrating right? Well, in this blog I have mentioned few ways of how to repair auto ignition gas stove. So keep reading.
Here are some steps you can follow to repair an auto ignition gas stove:
- Check the Battery: If the auto ignition feature of your gas stove is not working, the first thing you should check is the battery that powers it. If the battery is dead, replace it with a new one and see if the auto ignition feature starts working.
- Check the Spark Plug: If the battery is not the problem, the next thing you should check is the spark plug. If the spark plug is damaged or dirty, it may not generate a spark, and the auto ignition feature will not work. Clean the spark plug or replace it if necessary.
- Check the Gas Supply: Make sure that the gas supply to the stove is not blocked or restricted. If the gas supply is not adequate, the auto ignition feature may not work.
- Check the Ignition Wires: If the battery, spark plug, and gas supply are all in good condition, the problem may be with the ignition wires. Check the wires for any signs of damage or wear and replace them if necessary.
- Consult the User Manual: If you are still having trouble with the auto ignition feature, consult the user manual for your gas stove. The manual may have troubleshooting instructions or advice on how to fix common problems.
- Call a Professional: If you are not comfortable working with gas stoves or if the problem persists after trying the above steps, it is best to call a professional to repair the auto ignition feature.
Remember, working with gas stoves can be dangerous, and it is important to follow safety precautions and proper procedures. If you are not familiar with the workings of gas stoves or if you are unsure about how to repair the auto ignition feature, it is best to call a professional.
Common Possibilities To Check Why Your Auto Ignition Gas Stove is Not Working
You need to have a check on the red button switch on the gas stove if is working or not, igniter’s efficacy must be verified and additionally, check whether the igniter is damaged and whether the wires are connected properly.
- An igniter needs to be replaced if it doesn’t work.
- If any of the wires are frayed or disconnected, you’ll need to supply replacements and check their connections
- Examine the ignition nozzles to ensure they are not blocked with moisture. In addition, wet burner caps, nozzles, or ports may cause an ignition failure.
- Gas supply problems should be considered. When the igniters make their clicking noise but the burners still won’t light, check the gas supply. If your hob is connected to a gas tank or to a natural gas line, make sure its gas connection is correct
Additional Information : How to repair auto ignition gas stove
- Step1 – The saddle valve near the unit should be turned off by unplugging your unit.
- Step2 – Take off the oven’s hood. You will not be able to lift the lid if you have sealed burners. A unit’s ignitors should be located near its burners. You can clean the ignitor with a toothbrush if it is dirty. It’s time to put the device through its paces
- Step3 – If the ignitors are malfunctioning, remove the burner dials from the unit’s front panel
- Step4 – Take the front cover of the oven apart by removing the screws at the ends where all of the gas supply knobs are connected.
- Step5 -Next, by sliding the switch forward, the wires needs to be pulled off the burner valve. Wires will be attached to the switch. The wires of the burner valve need to be loosed by loosening the screws that hold them down. Carefully yank the plug out of the wall. Get a new switch and plug the wires into it. Replacing a burner’s switch is as easy as sliding it onto the valve. Put the knob back in place, then flip the switch to the “gas on” position. Turn on the heat
- Step 6 – If the replacement switch doesn’t seem to be working, check inside the oven where the wires are connected to the switch. To install a module, seek out its housing, which measures about 3 by 3 inches. Pull the connectors on the wires to remove them from the module terminals. Pull the old module out by removing the screws. Orient the wires in the same way as before in the new module. The oven should be reassembled. Fire up the stove by turning on the power and the gas
Tip- An igniter spark should be a white colour with a light blue tint. The igniter’s electronic elements are defective if the spark is yellow or orange. In this case, get a replacement igniter made specifically for your stove’s make and model. To properly install an igniter, be sure to follow the steps outlined in the manual If auto ignition gas stove still won’t light after trying these solutions, it may be time to replace the complete igniter control module or igniter switch, or you can also call an expert for more detailed analysis